Call 08048981720 84% Response Rate

Send Email


Stepper Driver for Stepper motor
  • DSP based high performance stepper driver Amps capacity up to 8 Amps
  • DC/AC input supply provision
  • Auto accel/decel
  • Speed smoothness function
  • Inbuilt Enable/Disable, Error output function
  • Designed on same concept of close step driver
Dm542 Stepper Motor Drives
  • Dm542 Stepper Motor Drives
  • Dm542 Stepper Motor Drives
  • Dm542 Stepper Motor Drives

Dm542 Stepper Motor Drives

Product Price: Rs 2,100 / PieceGet Best Price

Product Brochure

Product Details:
Installation TypePANAL MOUNT
Output Power24VDc
Input Voltage24-48VDC
Output Current4.2Amp
Input PhaseSingle Phase
Model Name/NumberCE542
1. Voltage:24V-50VDC, peak current 4.2A
2. Apply for magnetic linkage vector resonance resistance algorithm and electronic damping lowspeed vibration arithmetic
3. Auto recognize motor parameters and auto tuning control parameters when power is on 4. Build-in micro-step algorithm, to achieve low micro-step control command, high micro-step operate effect
5. Receive differential and one terminal PUL/DIR command
6. Pulse, direction, enable signal port level compatible 4.5V-28VDC, no need to connect external resistor
7. Set positive edge, negative edge, one pulse or dual pulse and motor initial direction by serial port
8. Control command Max pulse frequency is 500KHz (Default is 200KHz)
9. Provide 15 gears micro-step subdivision value setting, to set 200 ~ 51200 any subdivision by Serial port
10. Have RS-232 and RS-4BS serial port, can set or control drive parameters.
11. Reliable, signal port is optical isolation
12. Over-voltage, over-current, under—voltage protection.
Get Best QuoteRequest A Callback


Product Price: Rs 4,500 / PieceGet Best Price

Product Details:
Input Phase70VAC
Model Name/NumberYKD2608-MH
Installation Typepanel mount
Peak Current7.2AMP

l  32 bit DSP control technology, low noise/vibration with excellent stability and low cost

l  16 constant-torque microstep settings, 256 microsteps the highest

l  Smooth and accurate current control, effectively reduce motor heats

l  350Kpps pulse response frequency

l  After step pulse stops for 200ms, output current automatically halve to reduce motor heat

l  Excellent smoothness in low frequency high microstep applications

l  Photoelectric isolated signal input/output, high anti-interference ability

l  Drive current adjustable (under 6A)

l  Input voltage range: AC18~80V

l  Fault protection: over current, over voltage, low voltage protection, etc.

l  Small size: 151*94*54mm, 0.5kg

Get Best QuoteRequest A Callback
Stepper Motor Driver
  • Stepper Motor Driver
  • Stepper Motor Driver
  • Stepper Motor Driver

Stepper Motor Driver

Product Price: Rs 4,000 / PieceGet Best Price

Product Brochure

Product Details:
Input Voltage20-70VAC
Installation Typepanel mount
Step Angle1.8 Degree
Output Power24V
Output Current6.0A
Model Name/NumberDMA860H
Input Phase20-70VAC
- DMA860H stepping motor driver,mainly for 86/110 2-Phase Stepping Motor,16 Micro step,max stpe is 51200Pulse/rev,Working current is range from 2.4A to 7.2A.
The DMA860H is a high performance microstepping drive based on pure-sinusoidal current control technology. Owing to the above technology and the self-adjustment technology (self-adjust current control parameters) according to different motors, the driven motors can run with smaller noise, lower heating, smoother movement and have better performances at higher speed than most of the drives on the markets. It is suitable for driving 2-phase and 4-phase hybrid stepping motors.

  1. Extremely cost-effective
  2. Good high speed performance
  3. Supply voltage up to 80VAC or +110VDC
  4. Output current up to 7.2A
  5. Self-adjustment technology
  6. Pure-sinusoidal current control technology
  7. Pulse input frequency up to 300 KHz
  8. TTL compatible and optically isolated input
  9. Automatic idle-current reduction
  10. 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev
  11. Suitable for 2-phase and 4-phase motors
  12. Support PUL/DIR and CW/CCW modes
  13. Short-voltage, over-voltage, over-current and short-cicuit protection
Digital Stepper Motor Driver,
DMA860H Stepper Motor Driver,
DMA860H Digital Stepper Motor Driver with micro stepping, Digital Stepper Motor Driver 24 to 80V, DMA860H 7.2A Digital Stepper Motor Driver ,
DMA860H Digital Stepper Motor Driver with micro stepping 24 to 80V 7.2A 

Additional Information:

  • Production Capacity: 100
Get Best QuoteRequest A Callback


Contact Us
Thank youYour Enquiry has been sent successfully.
© Zenex Automation. All Rights Reserved (Terms of Use)Developed and managed by IndiaMART InterMESH Ltd.